home *** CD-ROM | disk | FTP | other *** search
/ Tech Arsenal 1 / Tech Arsenal (Arsenal Computer).ISO / tek-05 / 3commisc.zip / APP_PS2.DOC < prev    next >
Text File  |  1992-01-02  |  8KB  |  183 lines

  1. Application Notes for use of All Chargecard on a PS/2 Model 30-
  2. 286, 50, 50Z, or 60 running 3Com 3+ or 3+Open DOS workstation 
  3. software.
  4.  
  5. Configuration 1 -   3+ DOS workstation OR
  6.                        (see also config.w3p and autoexec.w3p)
  7.                     3+Open DOS workstation - XNS protocols
  8.                        (see also config.w3o and autoexec.w3o)
  9.                     Full NetBIOS or partial (not shown)
  10.                     Windows/286 (No EMS, no Smartdrive)
  11.                     VGA
  12.                     1MB of motherboard memory
  13.                     3Com EtherLink/MC network adapter
  14.  
  15. Configuration 2 -   3+ DOS workstation OR
  16.                        (see also config.3p and autoexec.3p)
  17.                     3+Open DOS workstation - XNS protocols
  18.                     Full NetBIOS or partial (not shown)
  19.                     VGA
  20.                     1MB of motherboard memory
  21.                     3Com EtherLink/MC network adapter
  22.  
  23. *** CAVEATS:  
  24.  
  25. 1) On 3Com's 3+ network operating system, if full NetBIOS must be 
  26.    loaded high, you must use NetBIOS 1.2.1H, available 
  27.    for 3+ customers from 3Com by dialing XXX-XXX-XXXX.  
  28.    (This module is included with 3Com 3+Open systems.) 
  29.  
  30. 2) In a Model 50Z, both the LCC and PLCC adapters must be used.
  31.    Both are available separately from All Computer.  You lose the 
  32.    use of two expansion slots.
  33.  
  34. 3) In a Model 30-286, the PLCC adapter must be used.  This 
  35.    adapter is available separately from All Computer.
  36.  
  37. INSTALLATION AND CONFIGURATION PROCEDURE - Configuration 1
  38.  
  39. 1) Install the All ChargeCard hardware per instructions.  Follow 
  40.    the instructions VERY CAREFULLY.
  41.  
  42. 2) Use the IBM PS/2 Model 30-286 or 50/60 Reference diskette move 
  43.    the Packet Buffer RAM of the EtherLink/MC card to address 
  44.    C000-C5FF.
  45.  
  46. 3) Add 
  47.    device=<path>\allemm4.sys /RAM /FR=NONE /X=C000-C5FF /EXT=64
  48.  
  49.    line to config.sys.  Do not load any network drivers high 
  50.    at this time.
  51.  
  52.    /RAM - tells allemm4 to find any available logical RAM between 
  53.           640K and 1MB.  On a '286 PS/2, VGA memory (A000-AFFF, 
  54.           and B800-BFFF) is not available, neither is extra ROM 
  55.           BIOS memory (in which there are no ROMS, thanks PS/2)
  56.           (E000-EFFF) is not available either.  /RAM figures this 
  57.           out all by itself.
  58.  
  59.    /X=C000-C5FF - eXcludes the 24K RAM Packet Buffer area of the 
  60.                    EtherLink/MC card.This leaves the largest 
  61.                    contiguous area (104K) available (C600-DFFF).
  62.                    **This parameter MUST match the RAM Packet 
  63.                    Buffer area assigned using the PS/2 Reference 
  64.                    Diskette.
  65.  
  66.    /EXT=64 - Reserves the first 64K of extended memory (above 
  67.              1MB) for use by himem.sys.
  68.  
  69. 4) Install Windows/286, telling it that extended and expanded 
  70.    memory are available.
  71.  
  72. 5) Add remaining lines to config.sys and autoexec.bat per the 
  73.    appropriate config and autoexec files.  The first line of 
  74.    config.sys MUST be "device=himem.sys".  The second line of 
  75.    config.sys MUST be the "device=<path>\allemm4.sys..." line.  
  76.    The remaining "device =..." lines are in autoexec.bat.  All 
  77.    operating software includes its own "device," "files," 
  78.    "buffers," and "lastdriv" 'commands.'  That is why these are 
  79.    in autoexec.bat rather than config.sys.  
  80.  
  81.    The "alload" command loads drivers high.
  82.  
  83.    3+Open only:  In the \3open\doswksta\lanman\lanman.ini file, 
  84.    find the line containing the "redir" command.  Add to the 
  85.    front of it the full path to the alload command:
  86.    i.e.  \<path>\alload redir .....
  87.  
  88.  6) At this point you may want to experiment with loading drivers 
  89.     in different spots to obtain the best fit; you may also use 
  90.     the PS/2 Reference Diskette to move the location of the 
  91.     Packet Buffer RAM.  Don't forget to change the /X:... 
  92.     parameter of the "device=<path>\allemm4.sys..." line of 
  93.     config.sys to reflect the new location.  Use the alload, 
  94.     device, or xexamem commands interactively with no parameters 
  95.     to look at how memory is used.
  96.  
  97.     Useful parameters to load drivers in different places are:
  98.  
  99.     device /LM - loads driver into Low Memory (below 640K)
  100.     device /AF - Assigns (loads) driver into First available 
  101.                  segment
  102.     device /AT - Assigns (loads) driver into starting from the 
  103.                  end (Top) of available memory 
  104.  
  105.     alload (includes above parameters)
  106.     alload /SG:XX00 - loads driver into specified memory segment 
  107.                       (e.g. /SG:B000)
  108.  
  109.    ***Experiments have shown that spp.sys wants to be loaded 
  110.    first using the /AF command.  The order of the other device 
  111.    drivers does not matter, but the included autoexec.bat were
  112.    designed to obtain the best fit.
  113.  
  114. INSTALLATION AND CONFIGURATION PROCEDURE - Configuration 2
  115.  
  116. 1) Install the All ChargeCard hardware per instructions.  Follow 
  117.    the instructions VERY CAREFULLY.
  118.  
  119. 2) Use the IBM PS/2 Model 30-286 or 50/60 Reference diskette move 
  120.    the Packet Buffer RAM of the EtherLink/MC card to address C000-
  121.    C5FF.  This leaves the largest contiguous area (104K) 
  122.    available (C600-DFFF).
  123.  
  124. 3) Add 
  125.    device=<path>\allemm4.sys /RAM /FR=NONE /X=C000-C5FF 
  126.  
  127.    line to config.sys.  
  128.  
  129.    /RAM - tells allemm4 to find any available logical RAM between 
  130.           640K and 1MB.  On a '286 PS/2, VGA memory (A000-AFFF, 
  131.           and B800-BFFF) is not available, neither is extra ROM 
  132.           BIOS memory (in which there are no ROMS, thanks PS/2)
  133.           (E000-EFFF) is not available either.  /RAM figures this 
  134.           out all by itself.
  135.  
  136.    /X=C000-C5FF - eXcludes the 24K RAM Packet Buffer area of the 
  137.                    EtherLink/MC card.  
  138.                    **This parameter MUST match the RAM Packet 
  139.                    Buffer area assigned using the PS/2 Reference 
  140.                    Diskette.
  141.  
  142. 4) Add remaining lines to config.sys and autoexec.bat per 
  143.    attached files.  The first line of config.sys MUST be the 
  144.    "device=<path>\allemm4.sys..." line.  The remaining "device 
  145.    =..." lines are in autoexec.bat.  All operating software 
  146.    includes its own "device," "files," "buffers," and "lastdriv" 
  147.    'commands.'  That is why these are in autoexec.bat rather than 
  148.    config.sys.  
  149.  
  150.    The "alload" command loads drivers high.
  151.  
  152.    3+Open only:  In the \3open\doswksta\lanman\lanman.ini file, 
  153.    find the line containing the "redir" command.  Add to the 
  154.    front of it the full path to the alload command:
  155.    i.e.  \<path>\alload redir .....
  156.  
  157. 5) At this point you may want to experiment with loading drivers 
  158.     in different spots to obtain the best fit; you may also use 
  159.     the PS/2 Reference Diskette to move the location of the 
  160.     Packet Buffer RAM.  Don't forget to change the /X:... 
  161.     parameter of the "device=<path>\allemm4.sys..." line of 
  162.     config.sys to reflect the new location.  Use the alload, 
  163.     device, or xexamem commands interactively with no parameters 
  164.     to look at how memory is used.
  165.  
  166.     Useful parameters to load drivers in different places are:
  167.  
  168.     device /LM - loads driver into Low Memory (below 640K)
  169.     device /AF - Assigns (loads) driver into First available 
  170.                  segment
  171.     device /AT - Assigns (loads) driver into starting from the 
  172.                  end (Top) of available memory 
  173.  
  174.     alload (includes above parameters)
  175.     alload /SG:XX00 - loads driver into specified memory segment 
  176.                       (e.g. /SG:B000)
  177.  
  178.    ***Experiments have shown that spp.sys wants to be loaded 
  179.    first using the /AF command.  The order of the other device 
  180.    drivers does not matter, but the included autoexec.bats were 
  181.    designed to obtain the best fit.
  182.  
  183.